Note If you have a computer with multiple network adapters is multi-homed , you cannot enable the Windows Time service based on a network adapter. Important Windows Server has improved the time synchronization algorithms to align with RFC specifications.
Note In this case, if you want to set the clock back slowly, you would also have to adjust the values of PhaseCorrectRate or UpdateInterval in the registry to make sure that the equation result is TRUE. Note When you remove a Group Policy setting, Windows removes the corresponding entry from the policy area of the registry.
Warning This information is provided as a reference for use in troubleshooting and validation. Note Some of the parameters in the registry are measured in clock ticks and some are measured in seconds. Ticks Property. Submit and view feedback for This product This page. View all page feedback. In this article. Registers the Windows Time service to run as a service and adds its default configuration information to the registry.
Unregisters the Windows Time service and removes all of its configuration information from the registry. Monitors the Windows Time service. Converts a Windows NT system time measured in 10 -7 -second intervals starting from 0h 1-Jan into a readable format. Converts an NTP time measured in 2 -second intervals starting from 0h 1-Jan into a readable format.
Tells a computer that it should resynchronize its clock as soon as possible, throwing out all accumulated error statistics. Displays a strip chart of the offset between this computer and another computer. Displays the values associated with a given registry key. Displays the computer's Windows Time service information.
Enables or disables the local computer Windows Time service private log. Controls whether this computer is marked as a reliable time server. A computer is not marked as reliable unless it is also marked as a time server. Not a time server 0x Always time server 0x Automatic time server 0x Always-reliable time server 0x Automatic reliable time server The default value for domain members is Controls whether or not the chaining mechanism is disabled.
If chaining is disabled set to 0 , a read-only domain controller RODC can synchronize with any domain controller, but hosts that do not have their passwords cached on the RODC will not be able to synchronize with the RODC.
Specifies the maximum amount of time that an entry can remain in the chaining table before the entry is considered to be expired. Expired entries may be removed when the next request or response is processed.
The default value is 16 seconds. Controls the frequency at which an event that indicates the number of successful and unsuccessful chaining attempts is logged to the System log in Event Viewer.
The default is 30 minutes. Controls the maximum number of entries that are allowed in the chaining table. If the chaining table is full and no expired entries can be removed, any incoming requests are discarded.
The default value is entries. Controls the maximum number of entries that are allowed in the chaining table for a particular host. The default value is 4 entries. Specifies the smallest local clock adjustments that may be logged to the W32time service event log on the target computer. The default value is parts per million - PPM. Indicates the maximum number of seconds a system clock can nominally hold its accuracy without synchronizing with a time source.
If this period of time passes without W32time obtaining new samples from any of its input providers, W32time initiates a rediscovery of time sources. Default: 7, seconds. Controls which events that the time service logs. Time jump 0x2. Source change The default value on domain members is 2. The default value on stand-alone clients and servers is 2. Controls the rate at which the clock is corrected. If this value is too small, the clock is unstable and overcorrects.
If the value is too large, the clock takes a long time to synchronize. The default value on domain members is 4. The default value on stand-alone clients and servers is 4.
Controls the period of time for which spike detection is disabled in order to bring the local clock into synchronization quickly. Specifies that a time offset greater than or equal to this value in 10 -7 seconds is considered a spike.
Maintained by W32Time. Controls the dispersion in seconds that you must assume when the only time source is the built-in CMOS clock. Specifies the maximum offset in seconds for which W32Time attempts to adjust the computer clock by using the clock rate. Specifies the largest negative time correction, in seconds, that the service makes. Specifies the largest interval, in log2 seconds, allowed for the system polling interval.
Specifies the largest positive time correction in seconds that the service makes. Specifies the smallest interval, in log base 2 seconds, allowed for the system polling interval. Controls the rate at which the phase error is corrected.
On Windows systems, the hosts file must be opened as an administrator. For example, to add an entry to translate As we said above, the changes takes effect immediately. You will be able to example. For student or new user looking for computer system to start learning on, the easiest place to start is Windows 10…. Windows 10 is an operating systems created by Microsoft that runs on desktops, laptops, server and other devices.
Windows 10, Mac OS and other systems allow you to be productive, easy to use, reliable and enable you to install and run thousands of programs from gaming to productivity suite software for individuals and businesses. Hosts file is not a standard. Windows Defender running on Windows 8, by default, prevents the modification of the hosts file.
You have to change the configuration of Windows Defender so it can allow you to edit the hosts file. In Windows 10, you must access text editor as an administrator to carry out the necessary changes to the hosts file. To do that, you may have to log-in as an administrator to be able to save your changes.
The IP address is easily traceable. It is located within the cPanel through the following steps:. After getting the IP address from the cPanel, add a few lines to your hosts file, including the IP address and domain name.
What you want can be achieved by modifying the hosts file through Fiddler 2 application. Install Fiddler2. Click to select. You can achieve the same using nginx or apache but you will need to configure them. This doesn't give the requested result exactly, however, for what I was doing, I was not fussed with adding the port into the URL within a browser.
I think that what you are actually looking for is Virtual Hosts functionality. I use Apache so I do not know how other web daemons support this. Maybe it is called Alias. Here is the Apache documentation:.
Apache Virtual Hosts examples. Make sure the port is the default port "80" in my case this is what in the python flask: app. It is most powerful solution and this is just a really easy way to keep adding new subdomains, or to add new domains automatically when DNS records are pointed at the server. Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams?
Collectives on Stack Overflow. Learn more. Using port number in Windows host file Ask Question. Asked 10 years ago. Active 1 year, 1 month ago. Viewed k times. Improve this question. RayLoveless Charles Yeung Charles Yeung Maybe review this and switch the accepted answer to the netsh answer?
I ended up here when trying to figure out how to map. The question is: are you trying to redirect a whole host to a single port?!
0コメント